200-1907 March 2013 Optima 72 72-DVT30N Gas Fired Vented Room Heater (Direct Vent) For serial #42794 and up FOR USE WITH NATURAL GAS AND PROPANE*
72-DVT30N 10 FRAMING DIMENSIONS C B C A B * This dimension allows the top of the fireplace to slide under. If more rigidity
72-DVT30N 11 NOTE: See venting chart for maximum and minimum vertical / horizontal venting configurations. LOCATING GAS FIRE
72-DVT30N 12 ALLOWABLE TERMINATION LOCATIONS Canadian Installations (1) US Installations (2) Canadian Installations (1
72-DVT30N 13 APPROVED VENT COMPONENTS PART # DESCRIPTION 999-DV-TVK3 Archgard Flex Vent Kit with 36” (914 mm) vent length
72-DVT30N 14 VENTING - RESTRICTOR PLACEMENT NOTE: Vent restrictors are designed to reduce vertical stack action for vent
72-DVT30N 15 VENTING - VERTICAL TERMINATION CHART Chart is for one 90° bend, with a 1/4” (6 mm) minimum vertical rise pe
72-DVT30N 16 1. Maintain 1” (25mm) clearance (air space) to combustibles when passing through ceilings, walls, roof, enclos
72-DVT30N 17 NOTE: Galvanized pipe is desirable above the roofline due to its higher corrosion resistance. Continue to a
72-DVT30N 18 The Optima 72 can be used with Flexmaster Model GA 4” & 7” (101mm & 178mm) vent liners, and terminate
72-DVT30N 19 PART # DESCRIPTION 999-DV-TVK3 Flex Vent Kit with 36” (914 mm) vent length (includes 999-DV-HTC) 999-DV-TVK5
Requirements for the state of Massachusetts 5.08: Modifications to NFPA-54, Chapt
72-DVT30N 20 1. Place the Optima 72 in the framing. Locate the centerline of the termination and mark the wall. Cut an 11”
72-DVT30N 21 VENTING - HORIZONTALLY USING SIMPSON DURA-VENT DIRECT VENT SYSTEMS The Optima 72 can be vented horizontally usi
72-DVT30N 22 VENTING - HORIZONTALLY USING SIMPSON DURA-VENT DIRECT VENT SYSTEMS 1. Set the Optima 72 in its desired locatio
72-DVT30N 23 5. Mark the wall with an 11” (279mm) x 10” (254mm) hole. See termination framing on page 22. The center
72-DVT30N 24 ELECTRICAL CONNECTIONS, FAN SYSTEM WARNING: Before starting, make certain the power supply is turned OFF. The
72-DVT30N 25 LOG PLACEMENT The Archgard pan burner and fiber logs are designed to give a realistic fire package, and are cre
72-DVT30N 26 LOG PLACEMENT... Continued Step 2. Locate Log with 7201 stamped on the bottom and place it as shown. Step 1. Lo
72-DVT30N 27 LOG PLACEMENT... Continued Step 3. Locate Log with 7203 stamped on the bottom and place it at the rear as shown
72-DVT30N 28 LOG PLACEMENT... Continued Step 5. Locate Log with 6 stamped on the bottom and place it on the front pins as sh
72-DVT30N 29 LOG PLACEMENT... Continued Step 6. Locate Log with 7205 stamped on the bottom and place it on the front pins as
INTRODUCTION Congratulations on choosing an Archgard fireplace! The Optima 72-DVT30N is one of the most advanced direct vent fireplace heaters availa
72-DVT30N 30 OPTIONAL BRICK PLACEMENT WARNING: Failure to position the parts in accordance with these diagrams or failure
72-DVT30N 31 NOTE: Installing the panels in any other position other than shown will result in flame im-pingement causing s
72-DVT30N 32 NOTE: Installing the panels in any other position other than shown will result in flame im-pingement causing s
72-DVT30N 33 If a wall mounted switch or a wall mounted thermostat is desired, Archgard recommends that the device be wired
72-DVT30N 34 This appliance has a pilot which must be ignited using the sparker located next to the appliance valve controls
72-DVT30N 35 INITIAL OPERATION 1. Check that the appliance is properly vented and connected to the gas supply. 2. Check th
72-DVT30N 36 1. Set the thermostat to the lowest setting and turn the remote switch to “OFF”. 2. Turn off all electric pow
72-DVT30N 37 GLASS DOOR REMOVAL WARNING: Do not attempt to remove the glass door when the appliance is hot. 1. Remove the
72-DVT30N 38 LOUVER (UPPER & LOWER GRILLS) INSTALLATION The Optima 72 is packaged without the upper and lower louvers (g
72-DVT30N 39 TROUBLESHOOTING SYMPTOM ACTION Pilot will not light after pressing the sparker many times. 1. When lighting th
TABLE OF CONTENTS Caution and Safety Instructions 5 Appliance Certification, Installation Codes and Specifications, High Altitude Installation 6 Gas C
72-DVT30N 40 TROUBLESHOOTING Cont... SYMPTOM ACTION The main burner does not turn on with the pilot lit. Cont... 3. Check t
72-DVT30N 41 MAINTENANCE CAUTION: Do not conduct maintenance on the appliance while it is operating or while it is still ho
72-DVT30N 42 Before servicing, read the terms and conditions of the Archgard warranty at the back of the manual. Contact the
72-DVT30N 43 ADJUSTING PRIMARY AIR CHANGING MAIN BURNER ORIFICE NOTE: (Fig.1) is to give an example of a correct and incorre
72-DVT30N 44 1. Open the lower grills (louvers). 2. The pressure test taps are located on the valve. The taps are located
72-DVT30N 45 REPLACING CONVECTION BLOWER Caution: Label all wires prior to disconnection when servicing controls. Wiring err
72-DVT30N 46 Item # Item Description Qty Unit A 314-0015 Flex tub gasket 1 EA B 308-0120 Wing Nut, Plated Steel (
72-DVT30N 47 PARTS LIST - Logs and Pan Burner Item # Item Description Qty Unit 310-634720-1 Log 7201 1 EA 310-634720-2
72-DVT30N 48 REPLACEMENT PARTS LIST ARCHGARD OPTIMA 72 Item # Item Description Qty Unit 200-0200 Owner’s Manual 1 EA 3
72-DVT30N 49 REPLACEMENT PARTS LIST ARCHGARD OPTIMA 72 (continued) Item # Brick Panel Kit ( Quebec City Red) Qty Unit 72-
72-DVT30N 5 Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
This Limited Warranty is made by ARCHGARD INDUSTRIES LTD., hereinafter referred to as “Archgard”. Archgard warrants to the original purchaser of an
72-DVT30N 51 Frequently Asked Questions Listed below are some frequently asked questions about your Archgard Gas Fireplace.
Model # : 72-DVT30N Serial #: Date Installed: / / Name: Address: City: State/Prov: ZIP: Phone: ( _____ )
Archgard Industries Ltd. 7116 Beatty Drive Mission, B.C. V2V 6B4 Canada Website: www.archgard.com
72-DVT30N 6 SPECIFICATIONS This appliance is tested and safety approved under the following US and Canadian gas appliance st
72-DVT30N 7 Before connecting the appliance to the gas supply line, double check that the appliance you have purchased is de
72-DVT30N 8 APPLIANCE DIMENSIONS BACK 0” to stand-offs SIDES 0” to stand-offs TOP 0” to stand-offs BOTTOM 0” ADJ
72-DVT30N 9 MANTLE CLEARANCE NOTE: Low profile wooden crowns and moldings above the unit are not considered as mantles. I
Commentaires sur ces manuels