Archgard Optima 40 Spécifications télécharger pdf (Page 25)

Optima 40 - SB 25

1. Set the thermostat to the lowest setting and turn the remote

switch to “OFF”.

2. Turn off all electric power to the appliance if service is to be

performed.

3. Open lower louvers or access door.

4. Press slightly and turn control knob clockwise  to “OFF”.

Do not force.

5. Close lower louvers or access door.

Flame Adjustment Knob

Sparker

Control Knob

Automatic Valve

Sparker

Control Knob

Manual Valve

Pilot

A. This appliance has a pilot which must be lighted by a spark

ignitor. When lighting the pilot follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some

gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand

don’t try to repair it, call a qualified service technician.

Forced or attempted repair may result in a fire or

explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire of explosion may result causing

property damage, personal injury or loss of life.

1. STOP! Read the safety information above on this label.

2. Set the remote switch to “OFF”. Set the thermostat to the

lowest setting. (Only if your appliance is equipped with

these devices.)

3. Turn off all electric power to the appliance.

4. Open lower louvers or access door.

3. Press slightly and turn the control knob clockwise  to the

“OFF” position.

4. Wait 5 minutes to clear out any gas. Then smell for gas,

including near the floor. If you smell gas, STOP! and follow

instruction “B” above.

5. Find pilot. It is located between the logs near the center

behind the burner.

6. Press slightly and turn control knob counterclockwise  to

“PILOT”. Depress knob and light pilot by repeatedly

pressing the sparker. Once flame is established, hold knob

depressed for approximately 30 seconds. Release knob. If

pilot should go out, repeat steps 3 to 5.

• If the knob does not pop up when released, stop and

immediately call your service technician or gas supplier.

• If the pilot will not stay lit after serveral tries, turn the gas

control knob to “OFF” and call your service technician or

gas supplier.

7. If the appliance has a manual valve, turn gas control knob

counterclockwise  to the desired heat setting from “LO”

to “HI”. If the appliance has an automatic valve, turn gas

control knob counterclockwise  to “ON” and set the flame

adjustment knob to the desired heat setting from “LO” to

“HI”.

8. Set the remote switch to “ON”. Set the thermostat to the

desired setting. (Only if your appliance is equipped with

these devices.)

9. Turn on all electric power to the appliance.

10. Close louver or access door.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

303-0001 28MAY01

LIGHTING INSTRUCTIONS ON RATING PLATE

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 44 45

Commentaires sur ces manuels

Pas de commentaire

Archgard Optima 40 Spécifications Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Archgard Optima 40